How To Repair Igniter On Butane Cigar Lighter

There was a time I would go so frustrated with my torch lighter not working properly. I would get and then pissed off watching my lighter hiss and sputter or worse not even light at all. Present I can troubleshoot well-nigh problems and set up them in a couple of minutes and y'all can too. All it takes is a only piffling flake of learning.

The nigh common reasons why torch lighters stop working are:

Empty Fuel Tank
Fuel Adjustment Is To Loftier Or To Low
No Spark
Clogged Burners
Air Trapped In Fuel Lines

None of these common problems are difficult to fix and then if y'all accept a torch lighter that isn't working and want to fix it apace, keep reading.

Starting time off, do you have the instruction booklet that comes with most torch lighters? If so, check it out and meet what troubleshooting steps your item lighter has.

If you're saying "of course, I don't have that worthless instruction manual anymore!" Information technology's all good. Well-nigh torch and cigar lighters are basically the same when it comes to this stuff.

Step 1 DOES YOUR TORCH LIGHTER HAVE FUEL?

The thing I do know when it comes to helping someone who has a lighter trouble is to ask, "Is there fuel in it?" When you have a non-working lighter, this is probably the almost common issue.

Ninety percent of the time I get a frustrated look and a abrupt "of course there is!" About ten per centum of the fourth dimension I become a confused look and hear "um…I'yard not sure."

Ok and then…Does your torch lighter have fuel in it correct now?

If y'all are screaming "YES!! Information technology'due south got fuel! Only my torch lighter still isn't working." Move on to pace 2.

If you don't have fuel in your lighter, purge your lighter, and then add together some butane and see what happens. If you don't know how to purge and fill a lighter scroll down to the HOW TO FILL A BUTANE LIGHTER

Not sure if you take fuel in it? keep reading… Nosotros'll be getting to more on that afterward.

Ok, we accept a fueled torch lighter, now what?

Step 2 DOES YOUR LIGHTER HISS, OR Do NOTHING WHEN YOU DEPRESS THE TRIGGER

A torch lighter that is hissing when you depress the trigger means the fuel is going in the right direction.

If your torch hisses when you aren't depressing the trigger y'all probably have an internal leak or busted seal. That would be outside my power to assist and so get with the manufacturer.

Back to the hiss and wink or just hissing when you hit the trigger.

When yous hit the trigger and go nothing but a hiss you might accept the flame setting also high. Try lowering the flame setting and run into what happens. This is another common torch lighter not working effect.

Conversely, if you striking the trigger and either hear a depression hiss or zippo at all try turning up the flame adjuster and encounter what happens.

Footstep 3 ARE Yous GETTING A SPARK ON YOUR TORCH LIGHTER?

If after adjusting your flame up or down are you notwithstanding just getting a hiss or are you lot getting a wink and a hiss?

Continuing to get a hiss when you lot depress the trigger might suggest either yous aren't getting a spark or you might need to keep working on the flame adjustment.

When you don't accept a spark it could be a couple of things. First off, the worst-case scenario would be that the ignition is dead. More commonly, the igniter stop might exist muddy.

I apply a tin can of compressed air to blow over and clean the terminate of the igniter when I accept a torch lighter not working properly.

Check to see if you take a spark. If y'all have a good spark and hear a hiss or have a flash and hiss you lot're moving in the correct direction.

Step four DOES Y'all LIGHTER FLASH OR Chop-chop FLAME OUT?

When you accept a torch lighter not working correctly and striking the trigger, do you get a quick flash or does information technology ignite only to fire out quickly?

If you lot become a quick flash and continues hissing and/or have a weak-looking flame grab a tin can of compressed air. Use the compressed air to clean out the burner or burners of your non-working torch lighter.

Impurities from cheap butane as well as pocket lint besides every bit other things can clog up your burners causing problems for your lighter. Ever use high-quality butane for your lighter. Click the following link for a few butane brands we suggest that are really high quality.

Step five IS YOUR TORCH LIGHTER PURGED?

Lastly, have you purged your lighter to become rid of all the air in the system?

If yous aren't sure or didn't purge your lighter before filling it with butane can cause your lighter to flash and hiss. Not purging lighters is probably the second common consequence that I come across a torch lighter not working correctly.

Before purging your lighter make sure in that location is no lit flame or any kind effectually you lot. Also, extinguish anything like cigars or cigarettes because butane is incredibly flammable.

First, brand sure your optics are protected. Utilize safety spectacles or goggles. Side by side, layout a rag on a desk or table. Concord your lighter vertically and use a purging tool or small screwdriver to depress the fill up stem at the bottom of your lighter.

Use caution hither! When you depress the make full stem there volition be a blast of propellant and butane that comes out quickly from the bottom of the lighter. You might take to do this several times until no more air, butane, or propellant comes out.

HOW TO REFILL A BUTANE LIGHTER – Torch Lighter Not Working Part two

Before you purge or try to fill up a butane lighter you need to make certain it is cooled off. You don't need to put information technology in the freezer or anything, but wait 5 minutes or so after using your torch.

Fuel Flow Aligning

Before you refill your lighter, turn the flame aligning all the way down.

Nigh lighters have arrows pointing to + / – for flame height. If your lighter doesn't have these arrows, turn the aligning clockwise.

purge-valve-how-to-fill-torch-top-torch-lighters

Purge the lighter.

Non that your flame adjuster is all the way downwardly. Permit's purge all the air from the lighter.

Many people brand the mistake of trying to fill a butane lighter with purging. As I mentioned in a higher place, purging ways nothing more than getting all the air and any leftover propellant from your torch lighter.

When purging, Ever keep the fill/purge valve away from your face!

torch-lighter-not-working-purging-a-lighter-toptorchlighters

Flip your lighter so the fill/purge valve is facing up. Over again, the valve is usually bottom.

Press the purge/fill up stalk with your screwdriver or lighter primal. The air and propellant is going to boom out of the valve stem. Once again, always keep the valve abroad from your face.

You lot'll know your lighter is completely empty when you tin depress the valve without hearing whatever more air come out.

Fill your lighter with butane

Grab your butane and requite your can a quick shake.

Flip your butane can and then the stem is pointing down.

Make sure your lighters fill valve is pointing up.

Firmly button the butane nozzle down over the fill valve of your lighter and printing down for 5 to 10 seconds. Typically you'll hear some hissing coming from the can as it fills.

torch-lighter-not-working-how-to-refill-a-lighter-toptorchlighters

Before Yous Fire Upwards Your Torch Lighter

Wait for 3 to 5 minutes before lighting upward your torch after you lot fill a butane lighter.

You may have to brand some adjustments to the fuel flow/flame adjuster to get the flame the size y'all want.

The Conclusion to a Torch Lighter Non Working Correctly

Later cleaning out your burners and igniter with compressed air and purging your lighter yous should be good to go. If you're still having problems with your torch lighter non working correctly, y'all may need to contact the seller or manufacturer for help.

Every fourth dimension I fill up whatever of my torch lighters I brand sure they are completely purged before filling with butane. Equally a full general rule for maintenance, I likewise used canned air to clean out burners and the igniter when I make full lighters.

To make sure you avert a torch lighter not working correctly simply follow these uncomplicated maintenance steps.

Lastly, Information technology is always best to use highly refined butane for filling torch lighters. Nosotros recommend using quality brands like XIkar Purofane or Colibri Butane. Nosotros also put together a postal service on how to detect the all-time butane for torch lighters that also has our tiptop five brands.

I genuinely promise this quick troubleshooting guide helps if you take a torch lighter not working perfectly for you lot.

As always if y'all accept comments or questions click here to use the contact page to get a agree of united states.